EIA-422 - ορισμός. Τι είναι το EIA-422
Diclib.com
Λεξικό ChatGPT
Εισάγετε μια λέξη ή φράση σε οποιαδήποτε γλώσσα 👆
Γλώσσα:

Μετάφραση και ανάλυση λέξεων από την τεχνητή νοημοσύνη ChatGPT

Σε αυτήν τη σελίδα μπορείτε να λάβετε μια λεπτομερή ανάλυση μιας λέξης ή μιας φράσης, η οποία δημιουργήθηκε χρησιμοποιώντας το ChatGPT, την καλύτερη τεχνολογία τεχνητής νοημοσύνης μέχρι σήμερα:

  • πώς χρησιμοποιείται η λέξη
  • συχνότητα χρήσης
  • χρησιμοποιείται πιο συχνά στον προφορικό ή γραπτό λόγο
  • επιλογές μετάφρασης λέξεων
  • παραδείγματα χρήσης (πολλές φράσεις με μετάφραση)
  • ετυμολογία

Τι (ποιος) είναι EIA-422 - ορισμός

STANDARD FOR SERIAL COMMUNICATION
Rs 422; Rs422; RS 422; RS422; TIA-422; EIA-422
  • Data rate versus line length chart, from RS-422 Annex A.1
  • RS-422 network with multiple receivers

EIA-422         
<communications, standard> (Formerly "RS-422") An EIA serial line standard which specifies 4-wire, full-duplex, differential line, multi-drop communications. The mechanical connections for this interface are specified by EIA-449. The maximum cable length is 1200m. Maximum data rates are 10Mbps at 1.2m or 100Kbps at 1200m. EIA-422 cannot implement a truly multi-point communications network (such as with EIA-485), although only one driver can be connected to up to ten receivers. The best use of EIA-422 is probably in EIA-232 extension cords. {Comparing EIA-422, 423, 449 to RS-232-C (http://rad.com/networks/1995/rs232/rs449.htm)}. {Details on RS-232, 422, 423 and 485 (http://rs485.com/rs485spec.html)}. (2002-10-05)
RS-422         
RS-422         
RS-422, also known as TIA/EIA-422, is a technical standard originated by the Electronic Industries Alliance that specifies electrical characteristics of a digital signaling circuit. It was intended to replace the older RS-232C standard with a standard that offered much higher speed, better immunity from noise, and longer cable lengths.

Βικιπαίδεια

RS-422

RS-422, also known as TIA/EIA-422, is a technical standard originated by the Electronic Industries Alliance that specifies electrical characteristics of a digital signaling circuit. It was meant to be the foundation of a suite of standards that would replace the older RS-232C standard with standards that offered much higher speed, better immunity from noise, and longer cable lengths. RS-422 systems can transmit data at rates as high as 10 Mbit/s, or may be sent on cables as long as 1,200 meters (3,900 ft) at lower rates. It is closely related to RS-423, which uses the same signaling systems but on a different wiring arrangement.

RS-422 specifies differential signaling, with every data line paired with a dedicated return line. It is the voltage difference between these two lines that define the mark and space, rather than, as in RS-232, the difference in voltage between a data line and a local ground. As the ground voltage can differ at either end of the cable, this required RS-232 to use signals with voltage magnitudes greater than 5 volts. Moving to dedicated return lines and always defining ground in reference to the sender allows RS-422 to use 0.4 V, allowing it to run at much higher speeds. RS-423 differs primarily in that it has a single return pin instead of one for each data pin.